It is not as straightforward as it appears to paint a house or a room. The fact that the outcome is as expected has its own set of tricks, which we will show to you here so that you can paint like a true pro.
1. HIGH-QUALITY RAW MATERIAL
First and foremost, selecting high-quality paint will make our job much easier. You want to paint that has a lot of coverage and performance, doesn’t spatter, dries quickly, is washable, and has a low odor.
2. WORK BY CLOTHES ON THE WALL
It will be easier to arrange your work if you divide the area to be painted into zones. Masking tape should be used to cover switches, frames, and baseboards, and a fine brush should be used to make cutouts on walls and cornices.
3. SELECT THE ROLLER CAREFULLY
Use a non-drip nap roller with a length of 20-30cm. Begin painting in one corner of the wall and work your way to the middle. With the roller, evenly distribute and spread the paint.
4. FROM THE TOP TO THE BOTTOM
To avoid problems with splices and joints, slide the roller vertically, always from top to bottom, in a uniform manner. It’s not about splattering paint across the canvas without rhyme or reason. The importance of symmetry and pulse cannot be overstated. Do you want to learn the W technique? Continue reading.
5. WALLS THAT ARE IRREGULAR
Remove the dust from the wall and fill in the joints and gaps with a repair putty. To remove excess putty, use painter’s tape, and a putty knife to apply it over the putty. Allow to dry, then sand and dust after each process. Apply two coats of finishing paint at the end.
6. HOW DO I REPAIR MY CANVAS?
Removes dust, filth, and grease stains off walls. Remove any loose paint as well. Putty holes and defects, then sand and dust once the putty is dry. Apply at least two coats of paint.
7. FOLLOW-UP CARE
After painting, quickly rinse the tools with water. If you have any leftover paint, use painter’s tape to seal the container and store it with the lid down to keep air out. The paint will last longer this way.
8. COVER UP YOUR APPLIANCES
Certain appliances are difficult to remove. This includes ACs, ceiling fans among others. If you have invested in the best 1.5 ton split AC you could find your home, it is likely you want to keep it safe. Remember to cover your appliances in at least two coverings of plastic to prevent any paint from ruining their exterior.
We all know that color is vital, but before you choose a color, consider the quality of the paint and the type of finish you want to achieve the effect you want. To avoid having too much or too little paint, choose the appropriate amount based on the surface you want to paint. Measure the walls, width by height, excluding windows and doors, to determine the surface you’ll be painting. Quality brushes and rollers (synthetic or natural wool) will better cover the surface, saving you money and allowing you to create a better finish.
Open the windows and paint during the brightest part of the day. This will help you to observe spots where you haven’t adequately covered them and appreciate the shade you choose. Because dirt on the walls does not blend in with the paint, it is vital to clean them thoroughly before applying the roller. This will allow for better adhesion. To remove dust and alcohol stains, as well as children’s crayon scribbles, use water and a neutral detergent. Vinegar is used to remove the mold, and fine sandpaper is used to paint the pen.
It’s vital to note that any cleaning should be done at least a day ahead of time so that the surface is completely dry before you begin painting. We recommend that you clean the surface dust before using any product. As you can see, any cracks, chips, or holes where paintings have been hanging should be repaired before painting. The fissures must be healed, then further opened with a chisel before being sealed or repaired with mortar. If there are any holes, simply fill them with sealant.
For faster results, use a brush to cut the joint between walls and ceilings, door frames, and windows before moving on to the roller. Protect neighboring places using painter’s tape, such as baseboards, switches, or frames in the case of doors, so that the paint only covers the surface to be painted. To avoid paint splatters around the home, cover the floor with corrugated cardboard instead of plastic or newspaper, as it ensures the absorption and drying of paint droplets.
APPLY THE W TECHNIQUE TO YOUR PROJECT
This technique is usually utilized with satin finishes and provides for uniform roll discharge. To paint a wall using this technique, begin at the top and work your way down, stopping only after you’ve covered a certain region or plane. We’ll have a good ending in no time.
The layers should be as thin as possible. Bubbles might form if you apply too much paint on one coat. Apply a small amount of paint and wait for it to dry before moving on to the next layer. To avoid bubbles or stains, always follow the manufacturer’s drying instructions and wait at least four hours between coats. Also, you should know! Apply two coats at the very least.
